Reasons to Change Door Lock
You can replace your door lock for a variety of reasons, from improving the security of your home to redecorating your entryway. You may need to change locks when your key becomes stuck or is difficult to turn.
Even DIY beginners can easily change their lock. Get the tools you need to begin.
Take off the lock that was previously used.
Removal of the lock that was in place before the door is a necessary step prior to installing the new one. This is especially crucial in the event that you suspect someone else has access to your home. It's also a good idea after you've moved into your new home, suffered a break-in or a roommate moved in. The process is much easier than you imagine and can be completed within a few minutes.
Begin by getting rid of the screws that attach the deadbolt faceplate on the frame of the door. To remove the faceplate, you'll have to remove screws from both sides. This will allow you to see the inside of the door and provide you with the knowledge of how to proceed with the next steps.
Once you have removed your old faceplate, you will have to remove the bolt and strike plate. Use a screwdriver or a wrench to loosen the bolt, and then take it out of the hole in the door. If the bolt is rusty, you might need to use a chisel remove it. When using a chisel remove the bolt, be careful not to damage the door frame.
Before you take down the old lock, be sure that your new deadbolt and doorknob will fit in the existing holes on the door. A lot of hardware stores and big box stores have a wide selection of locks and can assist you in choosing the right one. Get help if the lock you bought isn't the right one for your door.
While you are removing the old lock, search for small depressions or notches in the handle or around the trim. If you are able to locate them, you can use a straightened safety-pin or flat screwdriver in order to remove the handle.
After the screw in the handle is removed, you can begin to remove the knob from its spindle. To do this, locate the set screw at the base of the knob, and loosen. Next, you will need to remove the knob from the spindle. Finally, carefully remove the spindle from the door.
Install the new lock
It's a great idea to change the locks on your doors periodically, especially if you have been the victim of a break-in. It's an affordable, simple and efficient way to ensure that your home is safe. With a screwdriver, and a few basic steps most people can do it themselves. You may also wish to learn how to change the lock's key to ensure that only you have the key.
You will need to purchase a new lock that has the same keyway as your existing lock. You can save money if you rekey the lock yourself. The majority of locksmiths charge a fee to do this. You can purchase the new lock at hardware stores or on the internet. A standard deadbolt should fit on most doors however, you'll have to measure the area on your door to make sure that it fits.
The majority times the lock you purchase will include an image of a cardboard model that shows how it will fit on the door. You can use it as a guide for drilling the hole, which is much easier than measuring every time. If the template does not line to your hole you need to return it to the hardware store and get another one.
You must install the new lock on the right-hand side of the door. You can confirm this by looking at the latch, which should be marked "up" or something similar. Make sure the latch is seated correctly in the plate, and then secure it using the provided screws.
If you are replacing a window door repairs locks glass hinges knob lock, it's also important to pay attention to the way it's operated. Most knob locks are left-handed, but there are some that are right-handed. If you're not careful, you may put the knob on the wrong side of the door, which would make it impossible to lock it from either the inside or the outside.
It is recommended to try the new lock after you've completed. You should be able to lock and unlock the door with keys from the inside as well as the outside. If you are not satisfied with the outcome, you can contact a locksmith to repair the issue.
Test the lock
A door lock that will not open can be a hassle however, it could also put your family's safety at risk. It's easy to solve the majority of door lock problems by tackling the issue and lubrication. Check that the key is properly cut and the Window Lock Repairs assembly is not loose or dirty. If this doesn't solve the issue, try lubricating the door lock actuator with powdered graphite or a silicone-based grease.
Make sure that the door lock switch, wiring harnesses and the actuator connector are working properly. To check this, refer to the manual or wiring diagram to determine the function and color-coding of all door lock switch wires. Then, use a test light or digital meter to determine whether the door lock actuator is receiving power and ground when the switches are turned on. If you see the switches switch on and off with voltage it means that the switches are in good shape and the actuator is likely to require replacement.
If the switch appears to work but the actuator doesn't move when you turn it, there may be a problem with the cylinder. The actuator cylinder is outfitted with pins that are spring-loaded. They prevent the cylinder from moving until the key is inserted, and then they push them upwards to match the height of the key at the location. This causes the cylinder eventually to rotate, opening the lock body, allowing the handle latch to be opened.
If the door lock actuator still not functioning, you can remove it by using a small screwdriver. You will need to loosen the bolt that window locks repair it first and then remove the plastic cover that houses the electrical connector. Then you must disconnect the door lock actuator and let it fall. Then you should be able to find and remove the two 10mm bolts which hold the actuator in position. After the actuator is removed, you can disconnect the black electrical connector.
Replace the key
If your keyed deadbolt or door knob isn't working, you'll have to rekey it or replace upvc window lock it. It is not difficult to do this yourself and can save you some money. It is best to hire an expert locksmith inspect the locks for any problems prior to starting. This will give you peace of assurance that your home is safe and secure.
Remove the faceplate on the outside of the doorknob/deadbolt. If there are screws that hold the faceplate in place then use a screwdriver to remove it. Then, you can remove the inside faceplate using a screwdriver that has a flat head. After you have removed the faceplate, you can take the bolt and screw from the lock cylinder.
A locksmith can help determine if your lock is in need of replacement or changed. They can also provide guidance on the most effective security measures for your home. They can also make the necessary modifications to your door and frame for the perfect fit. They also offer an assurance on their work.
If you decide to rekey the lock you must first purchase a new key for it. It is essential to use a lock key that fits snugly. Using an incorrect key could damage the internal mechanism and prevent it from functioning. Insert the key into the lock to test its size. If it is flush with the plug, it's of the correct size. If the pins stick out of the top of the plug, they're too long.
You may want to replace your door lock for a variety of reasons, including:
If you're moving into an homeowner's house or lose keys, rekeying your lock is an economical alternative than replacing it. It's also less expensive than a full replacement. However, there are certain instances where rekeying an existing lock isn't possible. For example, if the lock is damaged or repeatedly blocked, it's the time to replace it.